Skip to content
Guides · bolts

Metric Bolt Torque Chart: 8.8, 10.9 and 12.9 (Free PDF)

Recommended tightening torque for metric class 8.8, 10.9 and 12.9 bolts from M5 to M30, coarse and fine thread, dry and lubricated, in N·m and ft-lb, with a one-page printable chart.

Updated November 21, 2026
Hands tightening a brake caliper bracket bolt with a click torque wrench on a car with the wheel removed

Short answer: An M8 class 8.8 bolt takes about 25 N·m, an M10 about 50 N·m and an M12 about 88 N·m with clean, dry threads. Class 10.9 bolts take about 40% more (M10: 72 N·m). Oiled threads need about 25% less, dry zinc-plated bolts about 15% less. Find your size and class in the chart below, or download the one-page PDF.

These are standard tightening values for metric bolts in property classes 8.8, 10.9 and 12.9, from M5 to M30, coarse and fine pitch. Each one tightens the bolt to 75% of its proof load from ISO 898-1, the clamping force fastener makers recommend for a joint that has to stay tight. The class is stamped on the bolt head, and the size is the thread diameter in millimeters, not the wrench size. If a service manual lists a torque for the bolt you are tightening, use that. For inch bolts, see the SAE bolt torque chart.

50 N·m
M10 class 8.8, dry
72 N·m for class 10.9.
126 N·m
M12 class 10.9, dry
88 N·m for class 8.8.
-25%
Lubricated threads
Oil, grease or anti-seize. Dry zinc plating: about 15% less.
M10 x 1.5
How sizes read
10 mm thread diameter, 1.5 mm between threads.
Printable metric bolt torque chart (PDF)
FormatUS Letter, 1 page
Classes8.8, 10.9, 12.9
SizesM5 to M30, coarse + fine
On the sheet
Coarse thread chart (N·m)
Fine thread chart (N·m)
Coarse thread chart (ft-lb)
Class head markings
Dry vs lubed rule

This article contains Amazon affiliate links. 33gears earns a commission on qualifying purchases. See our affiliate disclosure.

Metric bolt torque chart: coarse thread

Coarse pitch is the default metric thread: an M10 bolt with no pitch given is M10 x 1.5. Values are in newton-meters (N·m). “Dry” means clean plain steel or black oxide threads. “Lubed” means threads with oil, grease or anti-seize. Dry zinc-plated bolts fall between the two columns.

Metric bolt torque chart for class 8.8, 10.9 and 12.9 coarse thread bolts from M5 to M30, dry and lubricated, in newton-meters
Coarse thread torque in N·m. The same numbers are in the table below and on the printable PDF.
Size8.8 dry8.8 lubed10.9 dry10.9 lubed12.9 dry12.9 lubed
M5 x 0.86.24.68.86.6107.7
M6 x 1117.915111813
M8 x 1.25251936274332
M10 x 1.5503872548463
M12 x 1.75886612694147110
M14 x 2141105201151235176
M16 x 2218164312234365274
M18 x 2.5312234431323504378
M20 x 2.5441330610457712534
M22 x 2.5601451831623971728
M24 x 37615711,0537901,231923
M27 x 31,1168371,5441,1581,8051,354
M30 x 3.51,5141,1352,0941,5702,4471,835

Class 8.8 jumps slightly more than you might expect between M16 and M18. ISO 898-1 raises the 8.8 proof stress from 580 to 600 MPa for bolts over 16 mm, so larger 8.8 bolts are rated for a little more clamping force.

Metric fine thread bolt torque chart

Fine pitch bolts take a little more torque than coarse bolts of the same diameter, because the shallower thread leaves more steel in the cross-section. Cars use them on suspension, brakes, wheels and engine parts. Measure the pitch with a thread gauge before you pick a row. Values in N·m.

Size8.8 dry8.8 lubed10.9 dry10.9 lubed12.9 dry12.9 lubed
M8 x 1272039294634
M10 x 1.25534076578967
M10 x 1564280609470
M12 x 1.5926913299154115
M12 x 1.259672138103161121
M14 x 1.5152114217163254190
M16 x 1.5233175333250389292
M18 x 1.5350263485363566425
M20 x 1.5489367676507790593
M22 x 1.56594959126841,066800
M24 x 28306231,1498611,3421,007

Metric bolt torque chart in ft-lb

Many torque wrenches sold in the US read in foot-pounds first. This is the coarse thread chart converted to ft-lb (1 N·m = 0.738 ft-lb).

Size8.8 dry8.8 lubed10.9 dry10.9 lubed12.9 dry12.9 lubed
M5 x 0.84.63.46.54.97.65.7
M6 x 17.75.8118.3139.7
M8 x 1.25191427203124
M10 x 1.5372853406247
M12 x 1.756549937010981
M14 x 210478148111173130
M16 x 2161121230173269202
M18 x 2.5230172318239372279
M20 x 2.5325244450337525394
M22 x 2.5443332613460716537
M24 x 3562421777583908681
M27 x 38236181,1398541,331998
M30 x 3.51,1168371,5441,1581,8051,354

Class 8.8 vs 10.9 vs 12.9 bolts

The class number stamped on the head tells you the bolt’s strength. The first number times 100 is the tensile strength in megapascals (MPa), and the second number is the ratio of yield to tensile strength. A class 8.8 bolt has a tensile strength of 800 MPa and yields at about 80% of that.

Diagram of metric bolt heads stamped 8.8, 10.9 and 12.9
ISO 898-1 class markings. The maker’s mark usually sits next to the class number.
Class 8.8
Proof stress 580 MPa (600 above M16)
Most common
Medium carbon steel, quenched and tempered. Roughly equivalent to SAE Grade 5 and used for most general car bolts.
Class 10.9
Proof stress 830 MPa
High strength
Alloy steel, quenched and tempered. Roughly equivalent to SAE Grade 8. Suspension, brake caliper and drivetrain bolts.
Class 12.9
Proof stress 970 MPa
Highest strength
Alloy steel. Common on socket head cap screws and high-load machinery joints. Strong but brittle, and sensitive to hydrogen embrittlement if plated.
Careful
Never use a 10.9 or 12.9 value on an 8.8 bolt. A bolt with no class marking should be treated as lower strength than 8.8 (class 4.6 or 5.8) and tightened well below the 8.8 column.

How to read a metric bolt size (and the wrench size)

The number after the M is the outside diameter of the thread in millimeters, and the number after the x is the thread pitch, the distance between threads. An M10 x 1.25 bolt is 10 mm across the threads with 1.25 mm between them. The wrench or socket size is larger than the thread size, which is the most common reason people pick the wrong row.

Thread sizeCoarse pitch (mm)Wrench size (mm)
M50.88
M6110
M81.2513
M101.516 (17 on DIN bolts)
M121.7518 (19 on DIN bolts)
M14221 (22 on DIN bolts)
M16224
M182.527
M202.530
M222.534 (32 on DIN bolts)
M24336
M27341
M303.546

A 13 mm socket fits an M8 bolt, not an M13, and a 17 mm socket usually means an M10 bolt on older or DIN-standard hardware. Measure the thread with calipers when in doubt.

Dry vs lubricated metric bolt torque

Use the lubed column when threads have oil, grease or anti-seize. Most of the torque you apply goes into overcoming friction under the head and in the threads; only a small share stretches the bolt. Lubricant cuts that friction, so the same wrench setting clamps harder. The chart uses a nut factor (K) of 0.20 for dry steel and 0.15 for lubricated threads, which works out to 25% less torque. Fastenal rates dry zinc plating at 0.17, about 15% below the dry value.

Dry column
Clean, plain steel or black oxide bolts
No oil, grease or anti-seize
Threads wiped clean of old thread locker
About 15% under dry
Dry zinc-plated bolts
Unoiled zinc-flake coated bolts
Lubed column
Oiled or greased threads
Anti-seize compound
New bolts with a light oil film
Careful
A dry torque value on a lubricated bolt can push it past its yield point. The bolt stretches permanently, loses clamping force and can snap later.

How to torque a metric bolt

Clean threads and an even, gradual pull matter as much as the number on the wrench. You need a click or beam torque wrench that covers the range: a 3/8-inch drive wrench reading roughly 20 to 100 N·m handles M6 to M10, and a 1/2-inch drive reading up to about 300 N·m covers M12 to M16.

Clean the threads.
Wire-brush the bolt and chase dirty or rusty holes with a tap. Dirt and rust add friction and give a false reading.
Identify the bolt.
Measure the thread diameter and pitch, and read the class stamped on the head.
Pick the right column.
Dry for clean plain steel, lubed for oiled, anti-seized or plated threads.
Snug every bolt first.
Run all bolts in by hand, then snug them lightly so the parts sit flat.
Tighten in passes.
Bring the bolts to about half the final torque, then to full torque, working in a crisscross pattern on multi-bolt joints.
Pull smoothly to the click.
Hold the wrench by the handle grip and pull slowly at a right angle. Stop at the first click; extra clicks add torque.

When not to use a metric torque chart

Generic values suit general hardware, not parts with their own engineered spec. European and Japanese cars use many torque-to-yield and angle-tightened bolts, so check the service manual first.

Chart values are fine for
Brackets, mounts and accessories with no published spec
Machinery, bike and fabrication work
Replacement hardware of a known class
Checking whether a shop’s number is in the right range
Use the maker’s spec for
Cylinder head, main and connecting rod bolts
Torque-to-yield bolts (“torque plus angle”), which are replaced after use
Wheel bolts and lug nuts
Bolts threaded into aluminum, magnesium or plastic
Stainless (A2, A4) bolts

A spec written as “40 N·m + 90°” is a torque-to-yield bolt: tighten to the torque, then turn it a further quarter turn. Those bolts stretch on purpose and are designed for one use.

How metric bolt torque is calculated

Every value comes from torque = K x diameter x clamp load. The clamp load is 75% of the bolt’s proof load: the ISO 898-1 proof stress times the thread’s tensile stress area.

Find the stress area.
An M10 x 1.5 bolt has a tensile stress area of 58.0 mm².
Find the proof load.
Class 8.8 proof stress is 580 MPa, so the proof load is about 33.6 kN.
Take 75%.
The target clamp load is about 25.2 kN.
Multiply.
0.20 x 0.010 m x 25,225 N = about 50 N·m dry.

This matches Fastenal’s metric torque-tension chart. Other charts run higher because they aim for more clamping force: Bolt Depot lists 55 N·m for an M10 8.8 bolt and Fractory about 57 N·m, which works out to roughly 85% of proof load. Stay with one chart for a whole job.

Frequently asked questions

What is the torque for an M8 bolt?

An M8 x 1.25 bolt takes about 25 N·m in class 8.8, 36 N·m in class 10.9 and 43 N·m in class 12.9 with dry threads. Lubricated threads need about 25% less.

What is the torque for an M10 bolt?

An M10 x 1.5 bolt takes about 50 N·m in class 8.8, 72 N·m in class 10.9 and 84 N·m in class 12.9, dry. That is about 37, 53 and 62 ft-lb.

What is the torque for an M12 bolt?

An M12 x 1.75 bolt takes about 88 N·m in class 8.8 and 126 N·m in class 10.9 with dry threads.

What does 8.8 on a bolt mean?

It is the property class. The first 8 means a tensile strength of 800 MPa, and the second 8 means the bolt yields at about 80% of that, 640 MPa.

Is a 10.9 bolt the same as Grade 8?

They are close. Class 10.9 has a tensile strength of 1,040 MPa (about 150,000 psi), the same as SAE Grade 8, so it is the usual metric substitute.

Is M10 the wrench size?

No. M10 is the thread diameter in millimeters. An M10 bolt usually takes a 16 or 17 mm wrench.

Do zinc plated metric bolts need less torque?

Yes. Zinc plating lowers friction. Fastenal uses a nut factor of 0.17 for dry zinc-plated bolts against 0.20 for plain steel, so plan on about 15% less than the dry value.

Is there a printable metric bolt torque chart?

Yes. The free PDF on this page fits on one US Letter sheet with coarse and fine thread values in N·m, the coarse values in ft-lb and the class head markings.

Sources

Avatar photo
About the Author

James Kowalski

Automotive Writer

James Kowalski is a former ASE-certified mechanic turned automotive writer. With 10 years of hands-on experience in repair shops and dealerships, James specializes in practical topics like tires, brakes, performance upgrades, and truck accessories. He believes in empowering readers with the knowledge to make informed decisions about their vehicles, whether they're weekend warriors or daily commuters.

More from James Kowalski

How we reviewed this article

This article was researched against manufacturer records and editorially reviewed before publishing. We accept no payment for coverage. Some guides contain affiliate links; see our affiliate disclosure.