P0174 means the engine computer found a lean mixture on Bank 2 that it could not correct with more fuel. Bank 2 is the side without cylinder 1, so it appears only on engines with two banks, such as V6, V8 and flat engines. Together with P0171 it usually points to a shared cause. Fix it soon.
| Code | P0174 |
|---|---|
| Meaning | System Too Lean (Bank 2) |
| Severity | Fix promptly |
| Can I keep driving? | Short trips are usually fine, but fix it soon. A lean engine can run hot, misfire and damage the catalytic converter. |
| Most common cause | Vacuum leak (cracked hose, intake gasket or PCV hose) |
| Difficulty | Moderate DIY |
What does P0174 mean?
The computer checks the front oxygen sensor on each bank and adds or removes fuel to hold the mixture steady. When it has added fuel up to its limit on Bank 2 and the exhaust still reads lean, it sets P0174. That limit varies by make and engine, and many cars set the code once the total correction reaches about +25 percent.
Cylinder 1 sits on Bank 1, so Bank 2 is the opposite cylinder head. Look up your engine to confirm which side that is, because the layout differs between makes and models. Most inline engines have only Bank 1 and never set this code.
P0174 symptoms
- Rough idle or a stall when you stop
- Hesitation or a flat spot when you accelerate
- Lower mileage than normal
- Hissing from one side of the engine
- A check engine light, often with P0171 stored beside it
What causes P0174?
What else is stored matters more than any other clue. The same lean condition has two kinds of cause depending on whether the other bank is affected.
- Both banks lean, P0171 and P0174 together: the cause is shared by the whole engine. Think of a large vacuum leak such as the brake booster hose or throttle body gasket, a dirty MAF sensor, low fuel pressure from a weak pump or clogged filter, or a leaking PCV system.
- Bank 2 alone: the cause sits on that side. Check the intake manifold gasket on the Bank 2 side, the vacuum hoses that run to that head, a clogged injector on that side and an exhaust leak ahead of the Bank 2 oxygen sensor.
- Faulty oxygen sensor: rare, and a single bad sensor can mimic a one-bank fault. Rule out leaks and fuel delivery first.
Some engines use one MAF sensor per bank. On those, a failing sensor can set only one of the two codes.
How to fix P0174
- Compare the banks: with a scan tool, read the long term fuel trim for both banks. If both are high, work on shared causes. If only Bank 2 is high, work on that side. The scanner guide shows where these values appear.
- Check idle against load: trims that are worst at idle and improve at 2,500 rpm suggest a vacuum leak. Trims that worsen under load suggest the fuel supply or airflow measurement.
- Inspect the Bank 2 intake gasket area: look for cracked hoses and listen for hissing. A smoke test finds leaks at the gasket faces.
- Clean the MAF sensor: use MAF cleaner only. Other solvents damage the element.
- Test fuel pressure: a pump that holds pressure at idle but sags at higher rpm affects both banks.
- Check the Bank 2 exhaust: a leaking manifold or flex pipe ahead of the front sensor draws in air and fakes a lean reading.
Can you drive with a P0174 code?
Yes for short trips, with a repair in the next few weeks. Lean running raises combustion temperature and can cause misfires, which damage the catalytic converter over time. If the light flashes or the engine bucks under load, stop and have it towed rather than drive on.
Related codes
- P0171: System Too Lean (Bank 1)
- P0172: System Too Rich (Bank 1)
- P0101: Mass or Volume Air Flow Sensor A Circuit Range/Performance
- P0300: Random/Multiple Cylinder Misfire Detected
FAQ
Can P0174 appear without P0171?
Yes. A problem confined to Bank 2, such as an intake gasket leak on that side or one clogged injector, sets P0174 alone. A shared cause normally sets both, though one bank can cross the limit a few days before the other.
Should I replace the MAF sensor for P0174?
Clean it first and watch the trims. A MAF sensor is the cause mainly when both banks run lean. If cleaning changes nothing and the trims stay high, test the sensor reading against the engine’s load before you buy a new one.
Does P0174 mean a bad catalytic converter?
No, but it can lead there. Running lean for long periods overheats the converter and can set a code such as P0420 later. Fixing the lean condition early protects it.
Why is only Bank 2 lean on my V8?
Something differs between the two sides. The usual suspects are an intake gasket leak, an injector or an exhaust leak on that bank. Swapping a suspect injector to the other bank and watching whether the lean code follows it confirms the fault.
Got more than one code? Enter them all in the OBD2 code lookup to see each meaning, severity and first check side by side. If you still need a reader, start with the best OBD2 scanners for beginners, then follow how to use an OBD2 scanner to pull freeze frame data before you clear anything.
Sources & References
- SAE J2012, diagnostic trouble code definitions: https://www.sae.org/standards/content/j2012_201612/
- California Air Resources Board, on-board diagnostics: https://ww2.arb.ca.gov/our-work/programs/obd-board-diagnostic-program
- EPA, vehicle emissions inspection and maintenance: https://www.epa.gov/state-and-local-transportation/vehicle-emissions-inspection-and-maintenance-im
How we reviewed this article
This article was researched against manufacturer records and editorially reviewed before publishing. We accept no payment for coverage. Some guides contain affiliate links; see our affiliate disclosure.


