P0016 means the engine computer sees the crankshaft and the intake camshaft out of step on bank 1. A stretched timing chain or a bad crank or cam sensor are the usual causes. If the engine runs normally you can drive to a shop, but a rattle or hard start means stop.
| Code | P0016 |
|---|---|
| Meaning | Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor A) |
| Severity | Fix promptly |
| Can I keep driving? | If the engine runs normally, a short drive to a shop is usually OK. If it rattles, runs rough or struggles to start, stop driving. Wrong timing can bend valves. |
| Most common cause | Stretched timing chain or worn tensioner and guides |
| Difficulty | Usually a shop job |
What does P0016 mean?
The crankshaft and camshaft turn in a fixed relationship, linked by a timing chain or belt. The computer reads a position sensor on each shaft and compares the two signals. P0016 sets when the intake cam signal arrives earlier or later than the crank signal says it should, by more than the valve timing system can explain.
That makes P0016 different from P0011 and P0014, which ask whether the valve timing system reached its target. P0016 is about the mechanical link between the two shafts. “Sensor A” is the intake cam on most engines, and the exhaust side version is P0017. Bank 1 is the side with cylinder 1.
P0016 symptoms
- Check engine light
- Long cranking or hard starting
- Rough running or misfires
- Rattle from the front of the engine, especially at cold start
- Loss of power
What causes P0016?
- Stretched timing chain or worn tensioner and guides: slack in the chain moves the cam out of position. Chains wear faster when oil changes run long.
- Faulty camshaft or crankshaft position sensor: a failing sensor gives a late or noisy signal that looks like a timing error.
- Timing belt or chain jumped a tooth: the timing is off by a whole tooth, which usually causes a more serious running problem.
- Damaged reluctor (tone) wheel or loose cam phaser: the sensor reads a ring or wheel on the shaft, and damage there distorts the signal.
- Wiring or connector problem: corroded or oil-soaked connectors are rare but easy to check.
How to fix P0016
- Check the oil: low or dirty oil wears chain tensioners and strains the variable valve timing system, which runs on oil pressure. Correct the level and grade first.
- Check for companion codes: P0340 points to the cam sensor circuit, and P0011 points to the valve timing system.
- Inspect sensor connectors and wiring: look for oil, damaged pins and rubbed insulation at both the crank and cam sensors.
- Look up your engine: chain stretch is a known pattern on some engines, including the GM 2.4, VW 2.0 TSI and Ford 3.5 and 3.7. A match shifts suspicion toward the chain.
- Have the timing checked: if the engine rattles, or the code returns after clearing, a shop should read live cam and crank correlation and measure chain slack. A timing belt past its replacement interval is suspect too.
Can you drive with a P0016 code?
If the engine starts easily and runs smoothly, a short drive to a shop is usually acceptable. Do not put it off for weeks.
Stop driving if the engine rattles, runs rough or struggles to start. On interference engines, wrong timing lets pistons hit open valves and bend them, and a worn chain can jump further out of time. The interactive engine model shows how the cams and chain connect to the crankshaft.
Related codes
- P0014: B Camshaft Position – Timing Over-Advanced or System Performance (Bank 1)
- P0011: A Camshaft Position – Timing Over-Advanced or System Performance (Bank 1)
- P0017: Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor B)
- P0012: A Camshaft Position – Timing Over-Retarded (Bank 1)
- P0340: Camshaft Position Sensor A Circuit (Bank 1 or Single Sensor)
FAQ
Can a bad cam sensor cause P0016?
Yes. A weak or failing cam or crank sensor sends a signal that arrives off schedule. Sensors are cheap to replace, but confirm the chain is not stretched first, because either one can set the code.
Is P0016 the same as a timing chain problem?
Not always. A stretched chain is the most common cause, but sensors, a damaged tone ring and wiring faults set P0016 too. A rattle at startup and a code that keeps returning point to the chain.
Can I drive with P0016 long term?
No. If a chain is the cause, it keeps wearing and can skip a tooth. That can damage valves and turn a chain repair into an engine repair.
Will an oil change fix P0016?
Rarely, but it is worth doing. Fresh oil of the right grade helps the tensioner and the valve timing system. It does not shorten a stretched chain.
Got more than one code? Enter them all in the OBD2 code lookup to see each meaning, severity and first check side by side. If you still need a reader, start with the best OBD2 scanners for beginners, then follow how to use an OBD2 scanner to pull freeze frame data before you clear anything.
Sources & References
- SAE J2012, diagnostic trouble code definitions: https://www.sae.org/standards/content/j2012_201612/
- California Air Resources Board, on-board diagnostics: https://ww2.arb.ca.gov/our-work/programs/obd-board-diagnostic-program
- EPA, vehicle emissions inspection and maintenance: https://www.epa.gov/state-and-local-transportation/vehicle-emissions-inspection-and-maintenance-im
How we reviewed this article
This article was researched against manufacturer records and editorially reviewed before publishing. We accept no payment for coverage. Some guides contain affiliate links; see our affiliate disclosure.


