P0011 means the intake (A) camshaft on bank 1 is turned further ahead than the engine computer asked for, or the valve timing system is not moving it as expected. Oil problems and a dirty or sticking VVT solenoid are the usual causes. Fix it soon.
| Code | P0011 |
|---|---|
| Meaning | A Camshaft Position – Timing Over-Advanced or System Performance (Bank 1) |
| Severity | Fix promptly |
| Can I keep driving? | Short trips are usually fine, but get it checked soon. Low or dirty oil behind this code can wear the engine. |
| Most common cause | Low, dirty or wrong grade engine oil |
| Difficulty | Moderate DIY |
What does P0011 mean?
Many engines change intake valve timing as speed and load change. The computer commands a target cam angle, an oil control solenoid routes engine oil to a phaser on the camshaft, and the cam position sensor reports the actual angle. P0011 sets when the actual angle stays ahead of the target, or the system cannot get the cam to the target within the allowed time.
Most makers call the intake cam “A” and the exhaust cam “B”. A few label them differently, so check the service information if your car is unusual. Bank 1 is the cylinder 1 side. On V6 and V8 engines the bank 2 version is P0021. If the cam is too far retarded instead, the code is P0012. The exhaust cam version is P0014.
P0011 symptoms
- Check engine light
- Rough idle, sometimes with a stumble at stoplights
- Hesitation and weak acceleration
- Ticking or rattle on a cold start
- Worse fuel economy
What causes P0011?
- Low, dirty or wrong grade oil: the phaser moves on oil pressure, so thin, sludged or low oil is the first suspect. It is common and the cheapest to rule out.
- Sticking VVT solenoid or clogged solenoid screen: debris keeps the valve from moving freely, so oil never reaches the phaser at the right time.
- Stretched timing chain or worn tensioner: a loose chain changes where the cam sits relative to the crankshaft. Some engines have a known history of this.
- Worn camshaft phaser: the internal vanes or lock pin wear and the phaser cannot hold its angle.
- Faulty cam or crank position sensor: rare. A bad sensor usually sets its own circuit code.
How to fix P0011
- Check the oil first: read the dipstick, look at the condition and compare the oil in the engine with the viscosity in the owner’s manual. Change it if it is dark or overdue. An oil change with the right grade fixes a surprising number of these.
- Read the stored codes: P0012 or P0016 alongside P0011 point toward the timing chain rather than the solenoid.
- Remove the VVT solenoid: it sits near the front of the cylinder head or on the timing cover. Inspect its screen for sludge, then clean or replace it. Fit a new solenoid if the plunger sticks.
- Search for known issues on your engine: look for timing chain bulletins by engine code, since a new solenoid will not cure a stretched chain.
- Clear the code and retest: drive a few cycles. If P0011 returns, have the phaser and chain checked. Cam angle in live data, covered in how to use an OBD2 scanner, shows how far off the cam is.
Can you drive with a P0011 code?
Yes, for short trips, but have it looked at soon. The engine usually runs acceptably at low load, and the main risk is the oil condition behind the code.
Keep driving to a minimum if you hear a metallic rattle, feel misfires or see the oil light flicker. A rattling cold start with this code points to chain or phaser wear. The interactive engine model shows where the cams, phasers and chain sit.
Related codes
- P0014: B Camshaft Position – Timing Over-Advanced or System Performance (Bank 1)
- P0016: Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor A)
- P0012: A Camshaft Position – Timing Over-Retarded (Bank 1)
- P0021: A Camshaft Position – Timing Over-Advanced or System Performance (Bank 2)
FAQ
Can the wrong oil cause P0011?
Yes. Oil that is too thick delays phaser movement, and oil that is too thin or diluted loses pressure. Both can make the cam miss its target. Use the viscosity and spec printed in the manual, then retest.
Can I replace the VVT solenoid myself?
On most engines, yes. It is held by one or two bolts and unplugs from a connector, though a little oil will run out when it comes off. Replace the O-ring and clean the screen at the same time.
Will P0011 go away on its own?
The light may turn off after several clean drives if the cause was temporary, such as one low-oil episode. If the cause is a worn part, the code returns, usually within days.
Is P0011 expensive to fix?
It depends on the cause. An oil change or a solenoid is among the cheapest repairs on a car. A timing chain, tensioner and phaser job is one of the most expensive, so rule out oil and the solenoid before approving it.
Got more than one code? Enter them all in the OBD2 code lookup to see each meaning, severity and first check side by side. If you still need a reader, start with the best OBD2 scanners for beginners, then follow how to use an OBD2 scanner to pull freeze frame data before you clear anything.
Sources & References
- SAE J2012, diagnostic trouble code definitions: https://www.sae.org/standards/content/j2012_201612/
- California Air Resources Board, on-board diagnostics: https://ww2.arb.ca.gov/our-work/programs/obd-board-diagnostic-program
- EPA, vehicle emissions inspection and maintenance: https://www.epa.gov/state-and-local-transportation/vehicle-emissions-inspection-and-maintenance-im
How we reviewed this article
This article was researched against manufacturer records and editorially reviewed before publishing. We accept no payment for coverage. Some guides contain affiliate links; see our affiliate disclosure.


