Skip to content
Cars

Horsepower Converter: hp, kW, PS, bhp, Watts and Torque

Convert horsepower to kW, PS, bhp and watts as you type, turn torque and rpm into horsepower, and convert dyno wheel horsepower to crank horsepower.

Updated November 20, 2026
Big-block V8 engine seen from above with the valve cover removed, showing rocker arms and valve springs
Horsepower converter
Convert hp, kW, PS and watts, work out horsepower from torque, or find crank power from wheel power.
hp
bhp is the same as hp (mechanical). PS, CV, ch and pk are metric horsepower.
More units
fills the box with its hp
Result
300 hp = 223.7 kW
Every other unit
Tap a unit to put it in the headline.
223.7
304.2
300.0
223,710
299.9
22.8
165,000
How much is that?
01002003005007501,0001,500
300.0 hp
About the same as a 2005 Ford Mustang GT 4.6 (300 hp).
1 hp = 745.7 W. 1 PS = 735.5 W. Constants from NIST SP 811. The dial is in mechanical hp. Car figures are the makers’ published ratings.
What do you want to work out?
lb-ft
hp
rpm
Peak torque is usually 2,500 to 5,000 rpm. Peak power comes later.
Result
300 lb-ft at 5,000 rpm = 285.6 hp
hpmechanical horsepower
285.6
kWkilowatts
213.0
PSmetric hp (also CV, ch, pk)
289.6
lb-ftpound-feet
315.1
N·mnewton-meters
427.3
Torque and horsepower by rpm
Torque (lb-ft)HorsepowerCrossoverYour rpm
Horsepower and torque in lb-ft are equal at 5,252 rpm, because hp = lb-ft × rpm ÷ 5,252.
At 5,000 rpm you are below the 5,252 rpm crossover, so the lb-ft figure is larger than the hp figure.
The chart holds the torque above constant at every rpm to show how the two scales relate. A real engine’s torque changes with rpm. 1 lb-ft = 1.3558 N·m.
What do you want to work out?
hp
Drivetrain
GearboxDCT = dual-clutch
% of engine powerdefault
Choosing a drivetrain or gearbox sets the default. Type your own figure if you know it.
Typical for RWD automatic: 15-22%.
Result
300 hp at the wheels = 365.9 hp at the crank
18% drivetrain loss (default for RWD automatic): 65.9 hp is used up between the engine and the tires.
hpat the crank
365.9
kWat the crank
272.8
PSat the crank
370.9
Common mistake: wheel × (1 + 18%) = 354.0 hp. That is 11.9 hp below the real crank figure of 365.9 hp, because the loss is a share of the crank power, not of the wheel power.
Where the power goes
365.9 hp Engine
  Gearbox
  Driveshaft & diff
300.0 hp Wheels
82% of the power reaches the wheels. The loss is drawn in three equal steps; real cars split it differently.
Real drivetrain loss is partly a fixed amount, so a percentage is an estimate. Dyno to dyno readings also vary. The defaults are typical figures, not measurements of your car.

This horsepower converter turns any power figure into hp, kW, PS, bhp and watts as you type. It also does the two conversions spec sheets leave out: torque and rpm to horsepower, and wheel horsepower to crank horsepower with a drivetrain loss that matches your car. Type a number, pick its unit, and every other unit updates at once. The gauge shows where that figure sits next to real cars. If you only need one direction, use the kW to hp converter or the hp to kW converter.

Horsepower conversion formulas

One mechanical horsepower is 745.7 watts, so 1 hp = 0.7457 kW and 1 kW = 1.341 hp. To convert kW to hp, multiply by 1.341. To convert hp to kW, multiply by 0.7457. Metric horsepower (PS) is slightly smaller than mechanical horsepower: 1 PS = 0.9863 hp, a difference of 1.4%.

From To Multiply by
kW hp 1.3410
hp kW 0.7457
PS hp 0.9863
hp PS 1.0139
kW PS 1.3596
PS kW 0.7355
hp watts 745.7
watts hp 0.001341

The converter uses the exact definitions from NIST Special Publication 811: one mechanical horsepower is 550 foot-pounds per second, which works out to 745.69987 W, and one metric horsepower is 75 kilogram-force metres per second, or 735.49875 W. Electric horsepower is exactly 746 W.

How to use the horsepower converter

  1. Units. Type a number in the big field and tap the unit it is in. The cards below show it in every other unit. Tap a card’s copy button to copy that value. Search for a car to load its rated horsepower.
  2. Torque and HP. Enter torque in lb-ft or Nm and the engine speed in rpm to get horsepower and kW. Switch the direction to find the torque a given horsepower makes at that rpm.
  3. Wheel and Crank. Enter a dyno reading (wheel horsepower) and pick the drivetrain and gearbox. The converter fills in a typical loss and shows the crank horsepower. Switch the direction to estimate what a rated engine puts down at the wheels.

The page address updates as you work, so copying it from the address bar saves your numbers. A link you send opens the same conversion.

hp, bhp, PS, kW and whp: what each one means

Unit Name Size Where you see it
hp Mechanical horsepower 745.7 W US spec sheets and ads
bhp Brake horsepower Same unit as hp (or PS) UK and older US figures
PS Metric horsepower (Pferdestärke) 735.5 W German and European spec sheets
CV, ch, pk Metric horsepower in Italian, Spanish, French and Dutch 735.5 W Spec sheets in those countries
kW Kilowatt 1,000 W EU type approval, registration papers, EVs
whp Wheel horsepower Same unit as hp Chassis dyno results

bhp is not a different size of unit. The “brake” refers to how the power was measured: at the crankshaft, with a brake dynamometer holding the engine against a load. A figure in bhp is crank power, the same thing a manufacturer quotes as hp. British makers have used bhp for both mechanical and metric horsepower, so a UK “bhp” figure can be up to 1.4% off from US hp. The converter treats bhp as mechanical horsepower.

PS is why European and US figures for the same car rarely match. The engine is identical. Only the unit changes.

Car European spec sheet US spec sheet
Porsche 911 Carrera S (2025) 353 kW (480 PS) 473 hp
BMW M3 Competition 375 kW (510 PS) 503 hp
Volkswagen Golf GTI (Mk8) 245 PS 241 hp

480 PS converts to 473.4 hp, 510 PS to 503.0 hp and 245 PS to 241.6 hp, so each US figure is the European one in a different unit. A gap bigger than 1.4% means the cars really are different. The 2025 Golf GTI makes 265 PS in Europe but 241 hp in the US, because the US car kept the older engine tune to meet emissions rules.

kW is the legal unit in the EU, so registration documents and electric car specs use it. Most EV makers quote peak motor power in kW, which the car can hold for only a few seconds.

Horsepower to kW conversion chart

Common engine outputs in kilowatts and metric horsepower. For every value from 1 to 1,000, see the full hp to kW table or the kW to hp table.

hp kW PS
100 74.6 101.4
150 111.9 152.1
200 149.1 202.8
250 186.4 253.5
300 223.7 304.2
350 261.0 354.9
400 298.3 405.5
450 335.6 456.2
500 372.8 506.9
600 447.4 608.3
700 522.0 709.7
800 596.6 811.1
1,000 745.7 1,013.9

Horsepower to watts and watts to horsepower

One horsepower is 745.7 watts, and one watt is 0.001341 hp. To convert watts to horsepower, divide by 745.7. To convert horsepower to watts, multiply by 745.7. A 1,500 W space heater draws about 2 hp, and a 746 W electric motor is rated at exactly 1 electric horsepower.

Watts hp
1 0.001
100 0.134
250 0.335
500 0.671
746 1.000
1,000 1.341
1,500 2.012
2,000 2.682
3,000 4.023
5,000 6.705
7,500 10.058
10,000 13.410
hp Watts
0.25 186.4
0.50 372.8
0.75 559.3
1 745.7
2 1,118.5
2 1,491.4
3 2,237.1
5 3,728.5
10 7,457.0
100 74,570.0

Electric motor nameplates in the US use electric horsepower, which is exactly 746 W. The 0.3 W difference from mechanical horsepower is too small to matter for a motor, so most people use 746 for both. The converter keeps them separate under More units.

Torque to horsepower

Close-up of a car tachometer showing engine speed in thousands of rpm
Horsepower is torque multiplied by engine speed. Photo: Daniel Case, CC BY-SA 3.0.

Horsepower and torque are not separate measurements. Horsepower is torque multiplied by how fast the engine turns:

  • hp = torque (lb-ft) × rpm ÷ 5,252
  • kW = torque (Nm) × rpm ÷ 9,549

The 5,252 comes from the definition of horsepower: 33,000 foot-pounds per minute, divided by 2π to turn revolutions into radians. Because of it, horsepower and lb-ft are always equal at 5,252 rpm, and on every dyno chart plotted in those units the two curves cross there. Below 5,252 rpm the torque number is higher. Above it the horsepower number is higher.

Examples: 400 lb-ft at 3,000 rpm is 228.5 hp. 500 Nm at 4,000 rpm is 209.4 kW, or 280.9 hp. A spec sheet’s peak torque and peak horsepower arrive at different rpm, so you cannot get one peak from the other without the rpm where it occurs. That is why the converter asks for it.

Torque decides how hard the car pulls in a given gear. Horsepower decides how fast it can accelerate across the whole run, which is what our 0-60 calculator and quarter mile calculator model. Gearing turns engine torque into force at the wheels; the gear ratio calculator shows how. If you know a quarter-mile time or a 0-60 time but not the torque curve, the horsepower calculator works backward to an estimate.

Wheel horsepower vs crank horsepower

A car running on a chassis dynamometer in a factory test cell
A chassis dyno measures power at the wheels, after the drivetrain has taken its share. Photo: Marek Ślusarczyk, CC BY 3.0.

A manufacturer’s horsepower rating is crank horsepower: the engine’s output measured at the crankshaft on an engine dyno. A chassis dyno measures wheel horsepower (whp), what is left after the gearbox, driveshaft, differential and axles have taken their share. Wheel horsepower is always lower. The gap is the drivetrain loss.

These are the loss figures the converter uses as defaults. They are common conventions from tuners and dyno operators, not measurements of your car:

Drivetrain Gearbox Default loss Typical range 300 crank hp at the wheels
Front-wheel drive Manual 12% 10-15% 264.0 whp
Front-wheel drive Automatic or DCT 15% 12-18% 255.0 whp
Rear-wheel drive Manual 15% 12-18% 255.0 whp
Rear-wheel drive Automatic or DCT 18% 15-22% 246.0 whp
All-wheel drive Manual 20% 17-25% 240.0 whp
All-wheel drive Automatic or DCT 23% 20-27% 231.0 whp
Electric Single-speed 8% 5-12% 276.0 whp

To convert wheel horsepower to crank horsepower, divide by one minus the loss: crank hp = whp ÷ (1 − loss). A rear-drive manual car that makes 300 whp at 15% loss has 352.9 crank hp. The common mistake is to multiply by 1.15, which gives 345 hp and understates the engine by 8 hp. Going the other way, whp = crank hp × (1 − loss): a 300 hp rear-drive manual puts down about 255 whp.

Treat any percentage as an estimate. Part of the loss is a fixed amount of power it takes to turn the drivetrain, so a tuned engine making far more than stock loses a smaller share. Different dyno types read differently too: an inertia dyno such as a Dynojet usually reads higher than a load-bearing dyno, and a hub dyno reads closest to crank power. Electric cars lose less because they have a single-speed reduction gear instead of a multi-speed gearbox.

SAE gross vs net horsepower

White 1960s Ford Mustang fastback parked on a suburban street
Muscle car horsepower before 1972 was rated SAE gross. Photo: Tyler B, CC0.

Horsepower figures from American cars before 1972 are not comparable with modern ones, even in the same unit. Until then, US makers rated engines SAE gross: a bare engine on a test stand with no air cleaner, alternator, water pump load or full exhaust, and the ignition timing set for maximum power. From 1972 ads had to use SAE net, which tests the engine as installed in the car with all of its accessories.

There is no fixed conversion. Net figures run roughly 12% to 25% below gross for the same engine, and Chevrolet’s 1972 Chevelle made about 20% less power than the 1970 car. Part of that drop was real, because compression was cut that year for unleaded fuel. European DIN ratings were always net: the Porsche 356 Super 90 was rated 90 hp DIN and 102 hp SAE gross. A 1960s European figure therefore compares with modern numbers far better than a 1960s American one. The converter shows the rating standard when it names a classic car next to your number.

FAQ

How do you convert kW to hp?

Multiply kilowatts by 1.341 to get mechanical horsepower. 100 kW is 134.1 hp and 150 kW is 201.2 hp. For metric horsepower (PS), multiply by 1.36 instead.

How do you convert hp to kW?

Multiply horsepower by 0.7457. 100 hp is 74.6 kW, 200 hp is 149.1 kW and 300 hp is 223.7 kW.

Is bhp the same as hp?

Yes in size. Brake horsepower is horsepower measured at the crankshaft, which is what manufacturers quote. The word “brake” refers to the brake dynamometer used to measure it. Some British figures in bhp are actually metric horsepower, which is 1.4% smaller.

What is the difference between hp and PS?

PS is metric horsepower, 735.5 W. Mechanical horsepower (hp) is 745.7 W. So 1 PS is 0.9863 hp, and a car rated 300 PS makes 295.9 hp. European makers quote PS, US makers quote hp.

How many watts is 1 horsepower?

One mechanical horsepower is 745.7 watts. One metric horsepower (PS) is 735.5 watts, and one electric horsepower is exactly 746 watts.

How many horsepower is 1,000 watts?

1,000 watts (1 kW) is 1.341 horsepower.

What is whp?

Whp is wheel horsepower, the power measured at the driven wheels on a chassis dyno. It is lower than the engine’s rated horsepower because the gearbox, driveshaft and differential absorb some power on the way.

How do you convert wheel horsepower to crank horsepower?

Divide wheel horsepower by one minus the drivetrain loss. At a 15% loss, 255 whp ÷ 0.85 = 300 crank hp. Multiplying by 1.15 gives 293 hp, which is wrong.

How much horsepower is lost through the drivetrain?

About 12% to 15% for a front-wheel-drive manual, 15% to 18% for rear-wheel drive and 20% to 23% for all-wheel drive, with automatics at the higher end. Electric cars lose around 8%. These are conventions; real losses vary by car and by dyno.

How do you convert torque to horsepower?

Multiply torque in lb-ft by rpm and divide by 5,252. An engine making 350 lb-ft at 4,500 rpm produces 299.9 hp at that speed. For newton-metres, multiply by rpm and divide by 9,549 to get kW.

Why do torque and horsepower cross at 5,252 rpm?

Because 5,252 is the constant in the formula hp = lb-ft × rpm ÷ 5,252. At exactly 5,252 rpm the rpm and the constant cancel, so horsepower equals torque. It only happens when torque is in lb-ft; in Nm and kW the curves cross elsewhere.

Why are old muscle car horsepower ratings so high?

Before 1972 American engines were rated SAE gross, on a test stand without accessories or the production exhaust. Modern SAE net ratings test the engine as installed, which gives figures roughly 12% to 25% lower for the same engine.

Avatar photo
About the Author

James Kowalski

Automotive Writer

James Kowalski is a former ASE-certified mechanic turned automotive writer. With 10 years of hands-on experience in repair shops and dealerships, James specializes in practical topics like tires, brakes, performance upgrades, and truck accessories. He believes in empowering readers with the knowledge to make informed decisions about their vehicles, whether they're weekend warriors or daily commuters.

More from James Kowalski

How we reviewed this article

This article was researched against manufacturer records and editorially reviewed before publishing. We accept no payment for coverage. Some guides contain affiliate links; see our affiliate disclosure.