P0014 means the exhaust (B) camshaft on bank 1 is sitting further advanced than the engine computer commanded, or the variable valve timing system is not responding as it should. Dirty or low oil, a sticking oil control solenoid or a worn phaser cause most cases. Get it checked soon.
| Code | P0014 |
|---|---|
| Meaning | B Camshaft Position – Timing Over-Advanced or System Performance (Bank 1) |
| Severity | Fix promptly |
| Can I keep driving? | Short trips are usually fine, but get it checked soon. Low or dirty oil behind this code can wear the engine. |
| Most common cause | Low, dirty or wrong grade engine oil |
| Difficulty | Moderate DIY |
What does P0014 mean?
Variable valve timing (VVT) turns a camshaft slightly ahead of or behind the crankshaft to suit engine speed and load. The computer sends a command to an oil control solenoid, the solenoid directs oil pressure to a phaser on the cam, and the cam position sensor reports the result. P0014 sets when the reported exhaust cam position is too far advanced compared with the target, or the cam cannot reach the target at all.
“B” normally means the exhaust cam and “A” the intake cam, but a few makers label them differently, so confirm in the service information for your engine. Bank 1 is the side with cylinder 1. Only engines with variable timing on both cams can set this code. Its intake-cam counterpart is P0011, and the same fault on bank 2 is P0024.
P0014 symptoms
- Check engine light, often the only sign early on
- Rough or unstable idle
- Hesitation when accelerating
- Lower power and worse fuel economy
- Rattle or ticking for a few seconds after a cold start
What causes P0014?
- Low, dirty or wrong grade oil: the VVT system runs on oil pressure and oil that is thin, sludged or overdue for a change cannot move the phaser accurately. This is the most common cause.
- Sticking exhaust VVT solenoid or clogged screen: sludge or metal debris holds the valve in one position. The screen on the solenoid is a frequent culprit.
- Stretched timing chain or worn tensioner: slack in the chain shifts the measured cam position even when the solenoid works.
- Worn camshaft phaser: internal wear lets the phaser drift or fail to hold its position, often with a rattle on startup.
- Faulty cam position sensor: rare, and usually sets its own sensor code as well.
How to fix P0014
- Check the oil: confirm the level on the dipstick and look at the color and thickness. Use the exact viscosity and approval the maker lists. Change the oil and filter if it is dark or overdue.
- Scan for companion codes: P0015, P0013 or P0016 stored with P0014 narrow the fault. Save the freeze frame data before clearing anything, as covered in how to use an OBD2 scanner.
- Inspect the exhaust VVT solenoid: remove it, check the screen for debris and look for a stuck plunger or damaged O-ring. If your engine has identical intake and exhaust solenoids, swapping them shows whether the code follows the part.
- Look up your engine’s known issues: some engines have service bulletins for chain stretch or phaser wear. Replacing a solenoid will not fix those.
- Test the timing system: if the oil and solenoid are fine, a shop can check chain stretch and phaser operation with a scan tool and by measuring cam position. Chain and phaser work costs far more than a solenoid.
Can you drive with a P0014 code?
Short trips are usually fine, but do not leave it for months. If low or dirty oil caused the code, driving on it keeps wearing the cam phaser and chain.
Stop driving if the engine rattles loudly, runs rough enough to misfire or the oil pressure light comes on. Check the oil level first. A drop in level or a flashing check engine light changes this from a fix-soon problem to a stop-now problem.
Related codes
- P0011: A Camshaft Position – Timing Over-Advanced or System Performance (Bank 1)
- P0016: Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor A)
- P0015: B Camshaft Position – Timing Over-Retarded (Bank 1)
- P0017: Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor B)
- P0013: B Camshaft Position Actuator Circuit (Bank 1)
FAQ
Is P0014 caused by the oil?
Often, yes. Low level, old oil and the wrong viscosity all reduce the pressure the phaser needs. Change the oil with the grade your maker lists and clear the code. If it does not return over a week or two of driving, the oil was the cause.
Can I fix P0014 by cleaning the solenoid?
Sometimes. If the screen is clogged with sludge, cleaning it or fitting a new solenoid restores normal flow. If the cam still reads advanced afterward, the problem is further in, such as the phaser or the timing chain.
Will P0014 clear itself?
The light can go out after several clean drive cycles, but only if the fault stops. A sticking solenoid or low oil usually brings it back. Treat a code that returns as a real fault.
What is the difference between P0014 and P0011?
Both mean a cam is too far advanced. P0011 is the intake cam and P0014 the exhaust cam, so P0014 points to the exhaust solenoid and phaser. Oil and timing chain causes can set either one.
Got more than one code? Enter them all in the OBD2 code lookup to see each meaning, severity and first check side by side. If you still need a reader, start with the best OBD2 scanners for beginners, then follow how to use an OBD2 scanner to pull freeze frame data before you clear anything.
Sources & References
- SAE J2012, diagnostic trouble code definitions: https://www.sae.org/standards/content/j2012_201612/
- California Air Resources Board, on-board diagnostics: https://ww2.arb.ca.gov/our-work/programs/obd-board-diagnostic-program
- EPA, vehicle emissions inspection and maintenance: https://www.epa.gov/state-and-local-transportation/vehicle-emissions-inspection-and-maintenance-im
How we reviewed this article
This article was researched against manufacturer records and editorially reviewed before publishing. We accept no payment for coverage. Some guides contain affiliate links; see our affiliate disclosure.


